Fujitsu Printer FTP 627 Series User Manual

24V, 2" HIGH SPEED THERMAL PRINTER  
FTP-627 Series  
OVERVIEW  
The FTP-627 MCL Series consists of 24V drive ultra compact  
printers with 2 inch paper widths (58mm), which can print at  
high speed. Paper can be easily set by an unique platen  
release mechanism.  
The FTP-627 MCL series can be used for a variety of  
applications, such as portable terminals, POS, ticket issuing  
terminals, label printers, and measurement and medical  
equipment.  
HIGHLIGHTS  
• Ultra compact  
Height 15.5 mm, width 69.6 mm, depth 34.3 mm (MCL002)  
• High speed printing  
It can print at 60 mm/s (480 dotlines/s) maximum by using  
Fujitsu's unique head drive control.  
• With Auto Cutter  
Two types of compact cutters, a full cut and a partial cut, are  
in series.  
• High resolution printing / Kanji supported  
8 dots/mm of resolution printing is possible.  
• Easy paper setting  
Our unique platen release mechanism allows a  
wide paper route even if the printer is ultra-compact, so  
paper can be easily inserted. Auto loading is also available  
on MCL001, MCL003 and MCL303 models.  
• Two types of paper routes  
Front and bottom paper feed.  
• Easy mounting  
Head, motor, sensor and other component wiring are unified  
to one flexible cable, and the mechanism can be secured by  
one hook and two screws at two locations, making mounting  
easy.  
1
 
FTP-627MCL Series  
SPECIFICATIONS  
Item  
Specification  
Interface  
Conforms to RS232C / Centronics  
24 VDC ±5% average current, current approx. 1.1A (25 ˚ C,  
Rav=1500) 24V, simultaneously ON, 64 dots)  
For print head  
Power  
supply  
For motor of printer  
For motor of cutter  
24 VDC ±5%, 1A maximum  
24 VDC ±5%, 1 A maximum  
For logic  
5 VDC ± 5%, 0.2 A maximum  
Printer mechanism  
Mechanism with cutter  
Interface board  
83.5 x 35.7 x 15.5 mm (WxDxH), MCL003 (lever excluded)  
83.5 x 43.0 x 26.4mm (WxDxH), (screws and cables are excluded)  
131 x 89 x 24 mm  
Dimensions  
Weight  
Printer mechanism without  
cutter  
Approximately 55g  
Approximately 120g  
Printer mechanism with  
cutter  
Pulse resistance: 100 million pulses/dot (under our standard  
conditions). Abrasion resistance: paper traveling distance 50km  
(print ratio: 25% or less)  
Head  
Life  
Cutter  
300,000 minimum  
+5˚ C to +40˚ C (printing density assurance range, operation is  
possible at 0˚ C to +40˚ C)  
Operating temperature  
Operating  
environment  
Operating humidity  
Storage temperature  
Storage humidity  
20 to 85% RH (no condensation)  
-20˚ C to +60˚ C (paper not included)  
5-95% RH (no condensation)  
Head temperature detection Detected by thermistor  
Detection  
function  
Paper out/mark detection  
Head up detection  
Detected by photo-interrupter  
Detected by slide-switch (003/004/303#1/303#2 only)  
High sensitive paper:  
Standard paper:  
TF50KS-E4 (Nippon Paper)  
F60KS-E (Nippon Paper)  
FTP-020PU001, FTP-020P0104 (58mm)  
PD150R (Oji Paper)  
FTP-020P0701(58mm)  
Medium life storage  
paper:  
TF60KS-F1 (Nippon Paper)  
FTP-P0102 (58mm)  
Recommended thermal sensitive paper  
PD170R (Oji Paper)  
P220VBB-1 (Mitsubishi Paper)  
Long life storage paper:  
PD60R-N (Oji Paper)  
AFP-235 (Mitsubishi Paper)  
TP50KJ-R (Nippon Paper)  
HA220AA (Mitsubishi Paper)  
3
 
FTP-627MCL Series  
FUNCTION  
Item  
Item  
1.  
2.  
3.  
4.  
Test print function  
8.  
9.  
Cutter abnormality detection  
Motor power saving function  
Paper out detection  
Paper near end detection  
Head up detection  
10. Mark detection function  
11. MCU operation abnormality detection  
Thermal head temperature abnormality  
detection  
5.  
12. Power ON/OFF sequence protection  
6.  
7.  
Blow-out fuse detection  
13. Motor over-current protection  
14. Hardware timer  
Head voltage abnormality detection  
DIMENSIONS  
1. Printer mechanism  
Unit: mm  
4
 
FTP-627MCL Series  
2. Interface board  
130.8  
83.8  
55.9  
6.4  
4 - ø 3.6±0.1  
CN10  
CN11*  
CN8  
CN1  
30.5  
CN2  
CN5**  
5.1  
91.4  
5.1  
120.7  
Part mounting side  
Part solder side  
* CN11 used  
** CN5 used for paper near end detection  
Unit: mm  
5
 
FTP-627MCL Series  
PRINTER CONNECTOR (CN8) (FLEXIBLE PT BOARD) PIN ARRAYS  
Control circuit side connector: 52030-3010 Molex or equivalent product  
No.  
1
Signal  
PHK  
I/O  
Contents  
Photo interrupter (cathode)  
Photo interrupter (emitter)  
Head driving power supply  
Ground for head  
Data latch  
No.  
2
Signal  
VSEN  
I/O  
Contents  
Power supply for paper sensor  
Head driving power supply  
Ground for head  
Data input  
O
I
I
I
3
PHE  
VH  
4
VH  
5
6
GNC  
DIN  
I
7
GND  
LAT  
I
8
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
CLK  
STB5  
VDD  
STB 2  
TH  
I
Clock  
11  
13  
15  
17  
19  
21  
23  
25  
27  
STB6  
STB4  
STB3  
STB1  
TH  
I
Enable 6  
I
Enable 5  
I
Enable 4  
I
Logic Power supply  
Enable 2  
I
Enable 3  
I
I
Enable 1  
O
I
Thermistor  
O
I
Thermistor  
GND  
VH  
Ground for head  
Head driving power supply  
Open terminal  
GND  
VH  
Ground for head  
Head driving power supply  
Head open switch*  
N.C.  
SW2  
MT/B  
O
I
SW1  
MT/B  
I
Head open switch*  
I
Stepping motor coil  
excitation signal B  
Stepping motor coil  
excitation signal B  
29  
MT/A  
I
Stepping motor coil  
excitation signal A  
30  
MT/A  
I
Stepping motor coil  
excitation signal A  
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models  
6
 
FTP-627MCL Series  
INTERFACE  
1. Centronics interface  
(1) Connector (CN1)  
Connector part number  
: FCN-605Q030-G/S (Fujitsu Components) or equivalent  
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent  
(2) Connector pin assignment  
No.  
1
Signal  
PRSTB  
I/O  
Contents  
Data strobe  
No.  
2
Signal  
I/O  
I
Contents  
I
I
PRSTB-RET  
PRDT0-RET  
PRDT1-RET  
PRDT2-RET  
PRDT3-RET  
PRDT4-RET  
PRDT5-RET  
PRDT6-RET  
PRDT7-RET  
ACKNLG-RET  
BUSY-RET  
INPRM-RET  
INPRM  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Reset  
3
PRDT0  
PRDT1  
PRDT2  
PRDT3  
PRDT4  
PRDT5  
PRDT6  
PRDT7  
ACKNLG  
BUSY  
Data 0  
4
5
I
Data 1  
6
7
I
Data 2  
8
9
I
Data 3  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
11  
13  
15  
17  
19  
21  
23  
25  
I
Data 4  
I
Data 5  
I
Data 6  
I
Data 7  
O
O
O
I
Data input acknowledge  
Busy  
RINF2  
SLCTIN  
RINF1  
ATF  
Printer status 2  
Printer select  
Printer status 1  
Paper feed request  
27  
29  
O
I
RINF3  
O
Printer status 3  
GND  
Logic GND  
Notes:  
• Symbol ” means a negative logic signal.  
• “–RET” signal is a return signal of the twisted pair cable.  
• “I” or “O” means a signal direction from the interface board side.  
(3) Connector pin number  
(4) Data input signal timing  
FCN-605Q030-G/S(Fujitsu Components)  
PRDT0~7  
t1  
t3  
PRSTB  
BUSY  
t2  
t4  
ACKNLG  
t5  
Data set time  
PRSTB pulse width  
Data hold time  
PRSTB to BUSY= “H”  
ACKNLG pulse time  
:t10.5 µsec  
:t20.5 µsec  
:t30.5 µsec  
:t40.5 µsec  
:t55.0 µsec  
7
 
FTP-627MCL Series  
(5) Printer status signals  
Error status  
RINF1  
Low  
RINF2  
High  
High  
Low  
RINF3  
Low  
1. Paper out  
2. Paper near end  
High  
High  
High  
Low  
Low  
3. Head up  
Low  
4. Head temperature abnormality  
5. Head voltage abnormality  
6. Hardware abnormality  
7. Mark detection abnormality  
8. Normal  
Low  
High  
High  
High  
Low  
High  
High  
Low  
High  
Low  
Low  
Low  
High  
2. RS-232C  
(1) Connector (CN2)  
Connector part number  
: B6B-XH-A (J.S.T.) or equivalent  
Mating connector part number : XHP-6 (J.S.T.) or equivalent  
(2) Connector pin assignment  
No.  
1
Signal  
FG  
I/O  
-
Contents No.  
Frame ground  
No.  
2
Signal  
RD  
I/O  
Contents No.  
I
O
I
Receive data  
3
TD  
O
-
Transmission data  
Signal ground  
4
DTR  
DSR  
Data terminal ready  
Data set ready  
5
GND  
6
7
9
SLCTIN  
ATF  
I
I
Printer select  
8
INPRM  
I
I
Reset  
Power down cancellation  
signal  
Paper feed request  
10 PWD  
Notes:  
• Symbol ” means a negative logic signal.  
• “I” or “O” means a signal direction from the interface board side.  
Cutter (CN11)  
8
 
FTP-627MCL Series  
CONNECTOR PIN ASSIGNMENT  
1. Connector for power supply (CN10)  
Part number  
: B6B-VH White (J.S.T) or equivalent (board side)  
Mating connector part number: VHR-6 (J.S.T.) or equivalent  
2. Connector for printer mechanism connection (CN8)  
Part number  
: 52030-3010 (made by Molex) or equivalent (board side)  
No.  
Signal  
PHK  
I/O  
I
Contents  
Photo interrupter (cathode)  
Photo interrupter (emitter)  
Head driving power supply  
Ground for head  
Data latch  
No.  
2
Signal  
VSEN  
I/O  
O
O
O
O
O
O
O
I
Contents  
Power supply for paper senor  
Head driving power supply  
Ground for head  
Data input  
1
3
PHE  
VH  
4
VH  
5
O
O
O
O
O
O
I
6
GNC  
DIN  
7
GND  
LAT  
8
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
CLK  
STB5  
VDD  
STB 2  
TH  
Clock  
11  
13  
15  
17  
19  
21  
23  
25  
27  
STB6  
STB4  
STB3  
STB1  
TH  
Enable 6  
Enable 5  
Enable 4  
Logic Power supply  
Enable 2  
Enable 3  
Enable 1  
Thermistor  
Thermistor  
GND  
VH  
O
I
Ground for head  
Head driving power supply  
Open terminal  
GND  
VH  
O
O
O
Ground for head  
Head driving power supply  
Head open switch*  
N.C.  
SW2  
MT/B  
SW1  
MT/B  
Head open switch*  
Stepping motor coil  
excitation signal B  
O
Stepping motor coil  
excitation signal B  
29  
MT/A  
O
Stepping motor coil  
excitation signal A  
30  
MT/A  
O
Stepping motor coil  
excitation signal A  
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models  
9
 
FTP-627MCL Series  
OPTIONS  
Name  
Part Number  
Length (mm)  
500  
Interface Cable  
(between board and  
equipment)  
For Centronics (CN1) FTP-622Y201  
For RS232C (CN2)  
FTP-622Y301  
FTP-622Y401  
FTP-  
300  
300  
Power supply cable (CN10)  
Near end paper sensor (CN5) if required  
10  
 
FTP-627MCL Series  
COMMANDS  
Command  
Contents  
Moves print position to the next tab.  
Line feed.  
HT  
LF  
FF  
Feeds forms (new page).  
Sets reverse printing.  
ECS RS  
ESC US  
Resets reverse printing.  
Sets print mode.  
ESC ! + n  
ESC %+n  
ESC &+y+c1+c2+x+d1~dN  
ESC *+m+n1+n2+d1~dN  
ESC ?+n  
ESC 2  
Download character set specification//cancellation.  
Download character definition.  
Sets bit image mode.  
External registration character deletion.  
Sets 1/6 inch line feed length.  
Sets the line feed length.  
ESC 3+n  
ESC @  
Printer initialization.  
ESC A+n  
ESC C+n  
ESC D+d1~dN+NUL  
ESC J+n  
ESC K+n  
ESC R+n  
ESC c+1+n  
ESC d+n  
ESC e+n  
ECS s+n  
ECS t+n  
Sets the space between the line.  
Sets the page length by character line.  
Sets the tab position.  
Feeds paper in forward direction and prints.  
Reverse paper feed.  
Selects international character.  
Sets internal processing (including auto paper loading).  
Printing and n-line feeding.  
Prints and reverse feeds n-lines.  
Sets printing speed.  
Character code table selection.  
Sets/resets upside down printing.  
Kanji printing mode collective specification.  
Kanji printing mode specification.  
Kanji printing mode cancellation.  
Sets the detection functions.  
ESC {+n  
FS !+n  
FS &  
FS .  
FS 9+n  
11  
 
FTP-627MCL Series  
Commands continued  
Command  
Contents  
FS C+n  
Kanji code system selection.  
FS W+n  
Kanji double height and width mode specification/cancellation.  
Line feeds to the next mark.  
GS <  
GS A+m+n  
GS E+n  
Sets the line feed length after mark detection.  
Sets print quality.  
GS V+n+m  
GS e+n+m  
GS h+n  
Paper cutting.  
Sets bar code width.  
Sets bar code height.  
GS k+m+n+d1~dN  
GS w+n  
Selects bar code type and prints.  
Sets bar code width magnification.  
High speed collective image printing specified.  
Registration of image data.  
FS *+m+n1+n2+d1~dN  
GS &+m+x+y1+y2+d1~dN  
GS '+m+n  
FS E+n  
Prints registered image data.  
Correction of impressed energy.  
ESC V+n  
Right Rotation 90° specification / cancellation.  
Sets and cancels status transmission. (Serial Mode)  
Parameter transmission. (Serial Mode)  
Setting the amount of the feeding at automatic paper load.  
Setting the turning time of the motor excitation.  
Deletes recorded contents in flash memory.  
GS a+n  
FS r+n  
ESC EM+n  
ESC X+n+m  
ESC DEL+n  
Europe  
Japan  
Fujitsu Components Europe B.V.  
Diamantlaan 25  
2132 WV Hoofddorp  
Netherlands  
Fujitsu Component Limited  
Gotanda-Chuo Building  
3-5, Higashigotanda 2-chome, Shinagawa-ku  
Tokyo 141, Japan  
Fujitsu Components  
International  
Headquarter  
Offices  
Tel: (31-23) 5560910  
Fax: (31-23) 5560950  
Tel: (81-3) 5449-7010  
Fax: (81-3) 5449-2626  
Asia Pacific  
North and South America  
Fujitsu Components America, Inc.  
250 E. Caribbean Drive  
Sunnyvale, CA 94089 U.S.A.  
Tel: (1-408) 745-4900  
Fujitsu Components Asia Ltd.  
102E Pasir Panjang Road  
#04-01 Citilink Warehouse Complex  
Singapore 118529  
Tel: (65) 6375-8560  
Fax: (1-408) 745-4970  
Fax: (65) 6273-3021  
© 2003 Fujitsu Components America, Inc. All company and product names are trademarks or registered  
trademarks of their respective owners. Rev. 04/03/2003  
12  
 

Etymotic Research Headphones HF5 User Manual
Everpure Refrigerator CGCL1 User Manual
Fedders Humidifier AC1A Series User Manual
Festool Router 1400 EQ User Manual
First Virtual Communications Power Supply PS1010 3A User Manual
Fisher Price Baby Toy T7157 User Manual
Fisher Price Riding Toy K6670 User Manual
Fisher Price Riding Toy N1366 User Manual
Frigidaire Microwave Oven FMT144 User Manual
Gardena Blower 9333 20 User Manual