M A I N T E N A N C E / S E R V I C E
EH3500 Series
Environmental
Enclosure
C478SM-A (4/07)
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessories for the EH3508/EH3512/EH3515 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Accessories for the EH3515L Legacy Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
List of Illustrations
EH3515L Legacy Series Exploded Assembly Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
List of Tables
C478SM (4/07)
3
Important Safety Instructions
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not
be installed where exposed to rain and moisture.
3. Only use replacement parts recommended by Pelco.
4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify
the exposed parts have not been connected to line circuitry.
5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and lens
combination.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
4
C478SM-A (4/07)
Description
The EH3508/EH3512/EH3515 Series are indoor/outdoor light-duty camera enclosures designed for use with various cameras on the market and
accommodate fixed focal length lenses or motorized zoom lenses, with or without auto-iris operation.
The lid of the enclosure is hinged in the front providing easy access during installation and when camera/lens adjustments are necessary. The
camera sled itself serves as an elevation block. You can remove, flip, and then reinstall the sled to elevate the camera. All wiring and cabling is
brought into the enclosure through an adjustable gland at the bottom rear of the enclosure.
The rear link-lock latch can be used with a padlock of suitable size for applications requiring additional security.
The EH3515L Legacy® Series enclosures are used with pan/tilt units in Pelco’s PT480 Series. The enclosures are mounted on the bottom. A
connector in the pan/tilt unit attaches the enclosure, mechanically and electrically, to the pan/tilt unit.
MODELS
EH3500 SERIES
EH3508
Enclosure, indoor/outdoor, 8.75-inch (22.23 cm) lower body length. (CE)
EH3508-1
EH3508-2
EH3508-3
EH3512
EH3512-1
EH3512-1HD
EH3512-2
EH3512-2HD
EH3512-3
EH3512-3HD
EH3515
EH3515-1
EH3515-1HD
EH3515-2
EH3515-2HD
EH3515-3
EH3515-3HD
EH3508 with 120 VAC defroster and thermostatically controlled heater; 25 W
EH3508 with 24 VAC defroster and thermostatically controlled heater; 20 W
EH3508 with 230 VAC defroster and thermostatically controlled heater; 43 W
Enclosure, indoor/outdoor, 12.75-inch (32.38 cm) lower body length. (CE)
EH3512 with 120 VAC defroster, blower, and thermostatically controlled heater; 25 W
EH3512 with 120 VAC defroster and thermostatically controlled heater; 25 W
EH3512 with 24 VAC defroster, blower, and thermostatically controlled heater; 20 W
EH3512 with 24 VAC defroster and thermostatically controlled heater; 20 W
EH3512 with 230 VAC defroster, blower, and thermostatically controlled heater; 43 W
EH3512 with 230 VAC defroster and thermostatically controlled heater; 43 W
Enclosure, indoor/outdoor, 15.75-inch (40.00 cm) lower body length. (CE)
EH3515 with 120 VAC defroster, blower, and thermostatically controlled heaters; 25 W
EH3515 with 120 VAC defroster and thermostatically controlled heaters; 25 W
EH3515 with 24 VAC defroster, blower, and thermostatically controlled heaters; 20 W
EH3515 with 24 VAC defroster and thermostatically controlled heaters; 20 W
EH3515 with 230 VAC defroster, blower, and thermostatically controlled heaters; 43 W
EH3515 with 230 VAC defroster and thermostatically controlled heaters; 43 W
EH3515L LEGACY SERIES
EH3515L
Enclosure, indoor/outdoor, 15.75-inch (40.00 cm) lower body length. (CE)
EH3515L-1
EH3515L-1HD
EH3515L-2
EH3515L-2HD
EH3515L-3
EH3515L-3HD
EH3515 with 120 VAC defroster, blower, and thermostatically controlled heaters; 27 watts (CE)
EH3515 with 120 VAC defroster and thermostatically controlled heaters; 23 watts
EH3515 with 24 VAC defroster, blower, and thermostatically controlled heaters; 25 watts (CE)
EH3515 with 24 VAC defroster and thermostatically controlled heaters; 23 watts
EH3515 with 230 VAC defroster, blower, and thermostatically controlled heaters; 32 watts (CE)
EH3515 with 230 VAC defroster and thermostatically controlled heaters; 23 watts
C478SM-A (4/07)
5
Maintenance
Regularly scheduled maintenance prolongs the operational life and appearance of the equipment. Clean the window regularly with a soft cloth
using a mild, nonabrasive detergent and water to maintain picture clarity.
EXPLODED ASSEMBLY AND WIRING DIAGRAMS
EH3500 SERIES ENCLOSURE
G
Figure 1. EH3500 Series Enclosure Exploded Assembly Diagram
6
C478SM-A (4/07)
Table A. EH3500 Series Enclosure Exploded Assembly Parts List
Item
Qty
1
2
2
1
Description
Lid attachment pin
Type E clip
Gland
Body
Part Number
EH350010105
ZH.125ECLIP
1
2
3
4
HF00-1300-3500
37004001ASSY
37004000ASSY
35154000ASSY
GS07-0005-004A
8-inch enclosure
12-inch enclosure
15-inch enclosure
Bulb seal gasket
8-inch enclosure
12-inch enclosure
15-inch enclosure
Link latch lock
5
27 in.
36 in.
42 in.
1
6
7
LK01-0104-0400
1
Camera sled
EH35064236COMP
EH35004236COMP
8-inch enclosure
12-inch and 15-inch enclosure
Lid with latch
8
1
EH35084135COMP
EH35004235COMP
35154003COMP
EH35004141COMP
EH35004142COMP
MF00-3501-020A
HF00-1352-3500
EH350010107
ZHRVT1/8X3/8CE
ZH148X375X32C
ZH6-32X.375SPP
ZH05-0003-0605
ZH4-40X.375SPP
8-inch enclosure
12-inch enclosure
15-inch enclosure
Lid bracket hinge
Window bracket
Window and gasket
Gland nut
Lid spring
Rivet
Flat washer
9
10*
11
12
13
A
B*
C
D*
E
1
2
1
2
1
2
4
2
4
2
2
Screw, 6-32 x 3/8-inch, Phillips, pan head
Screw, 6-32 x 3/8-inch, Phillips, type F
Screw, 4-40 x 3/8-inch, Phillips, pan head
Nylon washer
F
ZH200X437X62N
ZH131X361X62N
ZH4-40NUTSH
ZH4LWSIS
8-inch enclosure
12-inch and 15-inch enclosure
Nut, 4-40, hex
G
H
4
4
Internal tooth lock washer, #4
*Applies only to EH3508, EH3512, and EH3515.
C478SM-A (4/07)
7
Table B. EH3508 Series Accessories Exploded Assembly Parts List
Item
Qty
Description
Part Number
I
1
Heater bracket
9484024
J
Heater, thermostatically controlled
1
1
1
HT21-0201-0100
HT02-1022-4310
HT23-0201-0100
120 VAC
24 VAC
230 VAC
K
Defroster, continuous-duty
1
1
1
1
1
4
4
1
8
1
HT21-1201-0100
HT02-0322-4306
HT23-1201-0100
PCB9100301ASSY
MF06-3500-16A
ZH05-0003-0605
ZHRVT1/8X3/8CE
ZH6-SFX.375SPP
ZH131X361X62N
ZH01-2001-0605
120 VAC
24 VAC
230 VAC
PC board
L
O
PC board cover
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
Pop rivet, 3/8-inch
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
Nylon washer
Screw, 6-32 x 3/8-inch, Phillips, pan head with lock washer
14
17
18
20
22
24 VAC Model Only
*
1
24 VAC rectifier
PCB9000277ASSY
* Illustrated in 24 VAC wiring diagram in Figure 3.
C478SM-A (4/07)
9
Table C. EH3512 Series Accessories Exploded Assembly Parts List
Item
Qty
Description
Part Number
I
1
Heater bracket
9484024
J
Heater, thermostatically controlled
1
1
1
HT21-0201-0100
HT02-1022-4310
HT23-0201-0100
120 VAC
24 VAC
230 VAC
K
Defroster, continuous-duty
1
1
1
1
HT21-1201-0100
HT02-0322-4306
HT23-1201-0100
PCB9100301ASSY
120 VAC
24 VAC
230 VAC
PC board
L
N
Blower
1
1
1
1
4
4
1
MM750010003
ED210005
120 VAC
24 VDC
MM750010003
MF06-3500-16A
ZH05-0003-0605
ZHRVT1/8X3/8CE
ZH6-SFX.375SPP
ZH6LWSIS
230 VAC*
PC board cover
O
14
17
18
19
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
Pop rivet, 3/8-inch
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
Internal tooth lock washer, #6
EH3512-1/-2/-3
4
2
8
2
EH3512-1HD/-2HD/-3HD
Nylon washer
Screw
20
21
ZH131X361X62N
EH3512-1/-3: 6-32 x 11/2-inch, Phillips, pan head
EH3512-2: 6-32 x 13/8-inch, Phillips, pan head
Screw, 6-32 x 3/8-inch, Phillips, pan head with lock washer
ZH6-32X1.50SPS
ZH6-32X1.25SPP
ZH01-2001-0605
22
1
24 VAC Model Only
**
1
24 VAC rectifier
PCB9000277ASSY
*Uses 120 VAC and resistor (resistor not included)
10
C478SM-A (4/07)
Table D. EH3515 Series Accessories Exploded Assembly Parts List
Item
Qty
Description
Part Number
I
1
Heater bracket
9484024
J
Heater, thermostatically controlled
2
2
2
HT21-0201-0100
HT02-1022-4310
HT23-0201-0100
120 VAC
24 VAC
230 VAC
K
Defroster, continuous-duty
1
1
1
1
1
HT21-1201-0100
HT02-0322-4306
HT23-1201-0100
PCB9100301ASSY
MF01-3500-018A
120 VAC
24 VAC
230 VAC
PC board
Rear heater bracket
Blower
L
M
N
1
1
1
1
MM750010003
ED210005
120 VAC
24 VDC
MM750010003
MF06-3500-16A
ZH05-0003-0605
230 VAC*
PC board cover
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
EH3515-1/-2/-3
O
14
4
6
6
4
4
8
2
EH3515-1HD/-2HD/-3HD
Pop rivet, 3/8-inch
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
Internal tooth lock washer, #6
Nylon washer
17
18
19
20
21
ZHRVT1/8X3/8CE
ZH6-SFX.375SPP
ZH6LWSIS
ZH131X361X62N
Screw
EH3515-1/-3: 6-32 x 11/2-inch, Phillips, pan head
EH3515-2: 6-32 x 13/8-inch, Phillips, pan head
Screw, 6-32 x 3/8-inch, Phillips, pan head with lock washer
ZH6-32X1.50SPS
ZH6-32X1.25SPP
ZH01-2001-0605
22
1
24 VAC Model Only
**
1
24 VAC rectifier
PCB9000277ASSY
*Uses 120 VAC and resistor (resistor not included)
C478SM-A (4/07)
11
120 VAC MODEL
INPUT, AC HIGH
INPUT, AC LOW (NEUTRAL)
1
2
3
4
DEFROSTER
DEFROSTER
DEFROSTER
BLOWER
(EH3512-1 AND
EH3515-1 ONLY)
5
6
7
8
9
FRONT HEATER
REAR HEATER
10
(EH3515 SERIES ONLY)
24 VAC MODEL
INPUT, AC HIGH
INPUT, AC LOW (NEUTRAL)
1
2
3
RED
BLK
RED
BLK
4
5
6
7
8
9
DIODE
BRIDGE
BLOWER
(EH3512-2 AND
EH3515-2 ONLY)
CAP
FRONT HEATER
REAR HEATER
10
(EH3515 SERIES ONLY)
230 V AC MODEL
INPUT, AC HIGH
INPUT, AC LOW (NEUTRAL)
1
2
RESISTOR
3
4
120 VAC BLOWER
(EH3512-3 AND
EH3515-3 ONLY)
5
6
7
8
9
FRONT HEATER
REAR HEATER
10
(EH3515 SERIES ONLY)
Figure 3. EH3508/EH3512/EH3515 Series Wiring Diagram
12
C478SM-A (4/07)
EH3515 LEGACY SERIES ENCLOSURE
G
Figure 4. EH3515L Legacy Series Exploded Assembly Diagram
Table E. EH3515L Legacy Series Exploded Assembly Parts List
Item
Qty
Description
Part Number
1
2
1
2
Lid attachment pin
Type E clip
EH350010105
ZH.125ECLIP
3
4
5
6
7
8
9
10
2
1
Gland
Enclosure body
Bulb seal gasket
Link latch lock
Camera sled
HF00-1300-3500
35154001ASSY
EH470010011
42 in.
1
1
1
1
2
1
2
1
LK01-0104-0400
EH35064236COMP
35154003COMP
EH35004141COMP
EH35004142COMP
MF00-3501-020A
HF00-1352-3500
EH350010107
Lid with latch
Lid bracket hinge
Window bracket
Window and gasket
Gland nut
11
12
13
Lid spring
NS
NS
NS
NS
A
B
C
D
E
F
G
H
1
1
1
1
2
4
2
4
2
4
4
4
Tilt table
Tilt table cradle
Tilt table gasket
Circuit board assembly
Rivet
35154005COMP
35154002COMP
351510000
PA05-0003-00B0
ZHRVT1/8X3/8CE
ZH148X375X32C
ZH6-32X.375SPPG
ZH6-SFX.375SPP
ZH4-40X.375SPP
ZH131X361X62N
ZH4-40NUTSH
ZH4LWSIS
Flat washer
Screw, 6-32 x 3/8-inch, Phillips, pan head
Screw, 6-32 x 3/8-inch, Phillips, type F
Screw, 4-40 x 3/8-inch, Phillips, pan head
Nylon washer
Nut, 4-40, hex
Internal tooth lock washer, #4
NS=Not Shown
C478SM-A (4/07)
13
Table F. EH3515L Legacy Series Accessories Exploded Assembly Parts List
Item
Qty
Description
Part Number
I
1
Heater bracket
9484024
J
Heater, thermostatically controlled
2
2
2
HT21-0201-0100
HT02-1022-4310
HT23-0201-0100
120 VAC
24 VAC
230 VAC
K
L
Defroster, continuous-duty
1
1
1
HT21-1201-0100
HT02-0322-4306
HT23-1201-0100
120 VAC
24 VAC
230 VAC
Blower
1
1
1
1
MM750010003
ED210005
120 VAC
24 VDC
MM750010003
MF01-3500-018A
ZH6-SFX.375SPP
230 VAC*
Rear heater bracket
Screw, 6-32 x 3/8-inch, Phillips, type F, pan head
EH3515L-1/-2/-3
M
14
4
6
6
2
4
2
EH3515L-1HD/-2HD/-3HD
Pop rivet, 3/8-inch
Internal tooth lock washer, #6
Nylon washer
17
19
20
21
ZHRVT1/8X3/8CE
ZH6LWSIS
ZH131X361X62N
Screw
EH3515L-1/-3: 6-32 x 11/2-inch, Phillips, pan head
EH3515L-2: 6-32 x 13/8-inch, Phillips, pan head
ZH6-32X1.50SPS
ZH6-32X1.375SPP
24 VAC Model Only
**
1
24 VAC rectifier
PCB9000277ASSY
*Uses 120 VAC and resistor (resistor not included)
**Illustrated in 24 VAC wiring diagram in Figure 3.
C478SM-A (4/07)
15
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
Exceptions to this warranty are as noted below:
1. Model and serial number
•
Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission
products.
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Three years on Spectra® IV products.
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product when
returned.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
Two years on Spectra III™, Esprit®, ExSite®, and PS20 scanners, including when used in
continuous motion applications.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
•
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair).
•
•
•
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
•
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product lia-
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any special, incidental or consequential damages
(including loss of use, loss of profit and claims of third parties) however caused, whether by
the negligence of Pelco or otherwise.
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C478SM
Date
8/98
8/99
Comments
Original version.
Added EH3508 Series and EH3515L Legacy® Series service and maintenance information. Revised the description, list of models, exploded assembly diagrams, parts
lists, and wiring diagrams.
C478SM-A
4/07
Updated wattages and parts lists. Added PCB cover to Figure 2 and ECO 05-10784. Revised to new format.
Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and Spectra III are trademarks of Pelco.
©Copyright 2007, Pelco. All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
|